خانه / مقاله / بررسی تجربی و تحلیلی رفتار تیرهای عمیق بتن مسلح با بتن مقاومت بالا تحت بار گسترده

بررسی تجربی و تحلیلی رفتار تیرهای عمیق بتن مسلح با بتن مقاومت بالا تحت بار گسترده

4 جولای, 2016 ارسال دیدگاه 775 بازدید

چکیده

در این مقاله رفتار تیرهای عمیق بتن مسلح با مقاومت بالا به صورت آزمایشگاهی بررسی شد. بدین منظور ۵ نمونه تیر عمیق بتن مسلح با مقاومت فشاری ۶۰ مگاپاسکال تحت اثر بار گسترده مورد آزمایش قرار گرفت. تیرهای آزمایشگاهی در دو انتها دارای تکیه گاه ساده و با آرماتورهای برشی قائم به فواصل مساوی تقویت شده بودند. آرایش آرماتورهای برشی نمونه ها یکسان ولی قطر آنها متفاوت بود. در طول آزمایش رفتار کلی نمونه های آزمایشگاهی مورد بررسی قرار گرفت. مشاهدات آزمایشگاهی شامل تغییر شکل وسط دهانه، وضعیت شکست، حالت های گسیختگی و مقاومت فشاری نظیر ترک خوردگی اولیه و شکست نهایی نمونه تیر عمیق بود. گسیختگی هر ۵ نمونه به صورت شکست ترد برشی بود. بر اساس نتایج حاصله، آرماتورهای قائم جان بر ظرفیت برشی تیرهای عمیق تاًثیرگذار بوده و نمونه ها تحت بار گسترده عموماً مقاومت برشی بالاتری در مقایسه موارد مشابه تحت بار متمرکز از خود نشان می دهند. نتایج آزمایشگاهی با نتایج به دست آمده از روش Strut-and-tie (مدل خرپایی) مقایسه گردید. نتایج حاصله از مقایسه حاکی از انطباق رضایت بخش مدل STM ارائه شده برای تیرهای عمیق بتن مسلح تحت بار گسترده با نتایج آزمایشگاهی می باشد .

چکیده [English]
Reinforced concrete deep beams have useful applications in many structures, such as tall buildings, foundations, offshore structures, and several others. The reinforced concrete deep as important structural elements having small span-to-depth ratio. The investigation of their behavior is a subject of considerable interest in RC structures researches and some studies on the shear strength of reinforced concrete deep beams have been carried out over the last fifty years. In deep beams, according to shear span-to-depth ratio and web reinforcement the ultimate strength is generally controlled by shear rather than flexure, if the sufficient amount of longitudinal reinforcement is used. Several different failure modes have been identified from experimental studies, due to variability in failure, the determination of their shear strength and identification of failure mechanism are very complicated. In this paper the influence of effective parameters on the behavior of high-strength RC deep beams was investigated. For this purpose, an experimental-analytical investigation was conducted; a total of five reinforced concrete deep beams with compressive strength in range of 60 MPa were tested under uniform contributed top loading. The tested specimens were simply supported and reinforced by vertical steel bars in various spacing. The general behavior of tested beams was investigated. Observations were made on mid-span vertical deflections, cracks form, failure modes and shear strengths. All the beam specimens showed a same response up to failure. The test results indicated that vertical web reinforcement are efficient in shear capacity of deep beams, all the specimens were failed at abrupt shear mode. According to the test results, the shear capacity is affected by amount of web reinforcement and the test specimens are stronger in comparison with those were tested under two-point loading. Elastic solutions of reinforced concrete deep beams provide a good description of the behavior before cracking, but after cracking, a major redistribution of stresses occurs and hence the beam capacity must be predicted by inelastic analysis. Due to their geometric proportions, the capacity of reinforced concrete deep beams is governed mainly by shear strength. Deep beams behave differently from shallow beams and have been identified as discontinuity regions where the strain distribution is significantly nonlinear and specific strut-and-tie models need to be developed, whereas shallow beams are characterized by linear strain distribution and most of the applied load is transferred through a fairly uniform diagonal compression field. Strut-and-tie method is one of the most simple and applicable methods which can be used to simplify analysis and design of deep beams. Strut-and-tie modeling is the most rational and simple method for designing no flexural members currently available. At least, the experimental strength of specimens was compared with predicted results of strut-and-tie method (STM). The performed comparison indicates that the STM to provide acceptable estimates of shear capacity of deep beam loaded under uniform loading.
کلیدواژگان [English]
deep beams, strut-and-tie, shear strength, shear reinforcement, contributed top loading
مراجع

 

  1. Foster, S. J, and Gilbert, R. I., 1998, Experimental Studies on High-Strength Concrete Deep Beams, ACI Structural Journal, V. 95, No. 4, pp.382-390.
  2. Siao, W.B., 1993, Strut-and-Tie Model for Shear Behavior in Deep Beams and Pile Caps Failing in Diagonal Splitting, ACI Structural Journal, Vol. 90, No. 4, pp. 356-363.
  3. Michael D. Brown, Cameron L. Sankovich, Oguzhan Bayrak, and James O. Jisra, Behavior and efficiency of bottle-shaped struts, ACI STRUCTURAL JOURNAL, Vol.103, No.3, 2006. pp. 348-355.
  4. Schlaich, J., and Schäfer, K.,1991, Design and detailing of structural  concrete using strut-and-tie models,  The Structural Engineer, Vol. 69,  No. 6, pp. 113-120.
  5. Marti, P., 1999, How to Treat Shear in Structural Concrete, ACI Structural Journal, Vol. 96, No. 3, pp. 408-415.
  6. Collins, M.P., and Mitchell, D., 1986, A Rational Approach to Shear Design – The 1984 Canadian Code Provisions, ACI Journal, Vol. 83, No. 6, pp 925-933.
  7. Ramirez, J.A., and Breen, J.E., 1991, Evaluation of Modified Truss-Model Approach for Beams in Shear, ACI Structural Journal, Vol. 88,No. 5, pp. 562-571.
  8. Tan, K., Kong, F., Teng, S., and Weng, L., 1997, Effect of Web Reinforcement on High-Strength Concrete Deep Beams, ACI Structural Journal, V. 94, No. 5, pp. 572-582.
  9. Kong, F. K., Robins, P. J., and Cole, D. F., 1970, Web Reinforcement Effects on Deep Beams, ACI Journal, V. 67, No. 12, pp. 1010-1016.
  10. Oh, J. K., and Shin, S. W., 2001, Shear Strength of Reinforced High-Strength Concrete Deep Beams, ACI Structural Journal, V. 98, No. 2, pp.164-173.
  11. A. Arabzadeh, 2001, Analysis of some experimental results of simply supported deep beams using truss analogy method, Iranian Journal of Science & Technology, Vol. 25, No. 1, Shiraz University,  IRAN, 2001, pp.115-128.
  1. A. Arabzadeh, A. R. Rahaei, R. Aghayari,  ۲۰۰۹,  A simple strut-and-tie model for prediction of ultimate shear strength of RC deep beams, International Journal of Civil Engineering, Vol. 7, No. 3, pp. 141-154
  2. CSA Standard CAN3-A23.3-94, 1994, Design of Concrete Structures for Buildings with Explanatory Notes, Canadian Standards Association, Rexdale, Ontario.
  3. ACI 318-02, 2002,Building Code Requirements for Structural Concrete and   Commentary, American Concrete Institute, Farmington Hills,  Michigan
  4. A. Arabzadeh, R. Aghayari, A. R. Rahaei, 2011,  Investigation of experimental and analytical shear strength of  reinforced concrete deep beams, International Journal of Civil Engineering, Vol. 9, No. 3, pp. 207-214.
  5. یوسف صحرائی، بررسی رفتار تیرهای عمیق بتن مسلح دو سر ساده تحت اثر بار گسترده یکنواخت. پایان نامه کارشناسی ارشد سازه، دانشگاه تربیت مدرس به راهنمائی دکتر ابوالفضل عربزاده، ۱۳۷۷٫

تگ ها:
رسته:
نوع مستند:
فرمت:
سال تولید:
لینک کوتاه: https://fattah-peiravian.com/?p=1824

دیدگاهتان را بنویسید

2026 طراحی توسط: - واحد فناوری اطلاعات مهندسی سازان